UPVC Replacement Door Handles

The handles on your doors get worn out over time and need to be replaced. It is important to match the dimensions of the handles you have previously replaced when replacing them.

The three measurements to check are the top screw's position, lever and key hole dimensions. Check the size guide for assistance in this.

Inline Lever/Lever

A lever handle is a modern-day door handle for patio door designed to work with new or replacement doors. This kind of handle is available in a variety of designs and finishes. This handle is available from several manufacturers including Avocet ERA Fullex Hoppe Mila Millenco Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The uPVC/Composite door handles are made of robust materials and are suitable for doors with multi-point locks that require a heavy duty design. The handles are inline and run off the same spindle and screw fixings so they can be easily fitted to new or existing uPVC/Composite doors.

The design of the sprung lever allows the handle for patio door to be positioned and angled to ensure a comfortable experience and is suitable for all users. The handle has been endurance tested to 200,000 cycles, this will ensure the quality of the finish as well as the performance of the handle over time. The sprung lever is adjustable to fit a wide range of locks. This is particularly useful for narrower doors where the cylinder is further away from the door. A shortened lever is also a good choice for doors where the latch could be opened by a thumb turn on the inside.

Lever Pad

A Lever Pad door handle made of upvc operates differently to the lever type handles found on most doors. These handles can work off one single spindle (inline) or independently from both sides using two inline or offset spindles (pad). They are typically used on UPVC doors with double glazing window handles glazing. They are available in a variety of finishes & variations.

The handles have been tested to at least 200 000 cycles and are available in a variety of finishes like White Silver, Chrome, & Gold. The finish is compliant with BS EN 1670:2007 Grade 5 and is also resistant to corrosion, giving the handle a high level of durability and performance for the intended use.

All of the UPVC lever pad designs come with screws and a spindle which allow them to be fitted on any new or existing uPVC door. The backplate fixation centres of 211mm allow for a bigger handle, which is usually beneficial when replacing a damaged or old multi-point door lock mechanism. These handle levers have springs, which eliminate the issue of door handles that sag out of the horizontal position when not in use.

It is crucial to match the dimensions of the PZ for both the multipoint lock and the uPVC doors when choosing a replacement UPVC spindle and handle. This measurement is also called the "handle centre" or "cylinder centres' and is a critical aspect in ensuring that you have the correct handles.

When you have the right PZ size you will then be required to make sure that the handle lever pads and push pads are a suitable shape to fit the American with Disabilities Act (ADA) compliant handles that you require for your doors. These are usually round or square, with an internal lever, and an external push pad.

The majority of UPVC Lever Pads that we sell are spring-loaded. This means that they return to a horizontal position when not being used instead of hanging and possibly sticking in the frame. This prevents drafts and cold air from entering a property. Also, the majority of UPVC lever pad handles are handed, allowing you to install them on either side of the door.

Euro Cylinder

Cylinder locks can be found on uPVC and other types of doors. They operate with a key to unlock a cylinder case which is then revealed with pins that can be aligned with the pins in the lock body, allow them to rotate an revolving cam, opening the door. euro lock handles cylinders can be fitted with up to six pins with internal and external doors usually needing different levels of security.

The choice of cylinder is vital. It is based on the amount of use your doors and handles will receive. For instance, exterior doors must be secured with an extra secure cylinder, while doors inside can be secured with the standard cylinder. Additionally, certain cylinders are available with extra features that increase security even more, like anti-drill and anti-bump characteristics.

A euro cylinder must be measured correctly to ensure it is the correct size for your door. The cylinder needs to be measured from the screw hole in the center to the ends of the cylinder. This includes the thumb turn if there is one. It is recommended to do this with the lock in place however in the event that this is not possible, you may remove it to measure. A cylinder that extends beyond the handle and escutcheon may be vulnerable to attacks, such as snapping locks, so it is important that it's not too long.

The design of most newer cylinders includes anti-drilling and bump resistance features. These are designed to reduce the chance of attack by forcing cylinders to turn in a different direction. This helps prevent attacks and keep your doors safe.

There are also cylinders that are designed to withstand snapping. This is a common attack on cylinders. A special tool is used to break the lock's break line and then the front of the cylinder is snapped off. This is much quicker and easier to achieve than gaining access through multipoint locks and leaves little evidence of a burglary, which could hinder the insurance claim.

Spring Cassette

This spring cassette is found in the base plate of the door handle. It provides a sprung solution to help return the multipoint lock handles to their original position after using. In the past, a lot of these types of handle did not have a spring integrated into them, and as a result, they are more likely to slide or 'drop' once the locking mechanism is disengaged. Adding this simple component is among the best methods to correct this, and is a great way to prevent your upvc doors from getting stuck in an open or closed position, as they aren't always simple to manually close by hand.

These spring cassettes have been specifically designed to be used with multipoint locks that are sprung, they will not fit non-sprung multipoint handles. You must have a custom hole cut into your backplate in order for them to fit (please check the image for a technical diagram). These cassettes are a replacement for damaged or missing cassettes on the backplate of uPVC door handles. They have a square cut out which accommodates an 8mm spindle and are sold as a set.

These spring cassettes are an excellent value-for-money way to fix the problem of handles on your doors that are sagging. They are simple to put in and will extend the life span of your uPVC doors. For more information about our selection of upvc door handle accessories and spares, contact us today. in touch with our team. We are here to assist you and give you professional advice. 📌 What's The Most Important "Myths" Concerning Upvc Replacement Door Handles Might Be True